Just How to Replace a Tub
Just How to Replace a Tub
Blog Article
Here down the page you might get a bunch of very good insight related to Installing A Bathtub.
Setting up a bath tub isn't specifically rocket science, yet it does call for strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a new one is likewise a reasonably tough job. If the old bathtub is conveniently easily accessible, the job can relocate immediately; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub as well as embeded in the brand-new one. Make certain you have actually qualified yourself for the job and are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed task, it is far better to think about utilizing one before you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly assist you set up a brand-new tub in your shower room if you have actually currently gotten a new tub and don't need to alter the plan of your previous water system pipes.
Your tools and material checklist should comprise the following:
Planning for the Installment
First of all, the supporting structure provided with the bath needs to be fitted (if called for) according to the maker's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make certain that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps system to prevent pressure on the tub.
Fit the flexible faucet connectors to the bottom of both faucets utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you use every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final setting.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of getting rid of the existing faucets can be quite troublesome as a result of the limited access that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a fabric all set for the remaining water that will come from the pipelines. As soon as the supply pipes have been eliminated, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from turning during this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned up of any type of old sealing substance.
Before proceeding to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Making use of both wood boards under its feet, position the bath tub in the required position. The wooden boards are valuable in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by examining the level and also readjusting the feet on the bath tub till the level checks out level.
To mount faucets, fit all-time low of the furthest flexible faucet adapter to the proper supply pipeline by making a compression join; then do the very same for the various other tap.
Switch on the water supply and also inspect all joints as well as new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise check the overflow electrical outlet and also the typical outlet for leakages.
Lastly, repair the bath paneling as defined in the maker's user's manual. Tiling as well as sealing around the bathtub should wait till the bath tub has actually been utilized at least when as this will certainly resolve it into its final placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin ensuring that the washers are in area between the tap and also the sink. Secure the faucet in position with the manufacturer given backnut. When the tap is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous type must be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to fracture a rigid seal, triggering the water to pass through the wall surface between the bathroom and also the tiling, leading to issues with wetness and feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your components and also fittings. They are offered in tubes and also cartridges, as well as can sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to enable the motion experienced when the bathtub remains in use. The sealant can split rather very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily available on the market. It is advisable to fit the ceramic tiles utilizing waterproof or water resistant glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our piece about Installing A Bathtub. Thank you for taking a few minutes to read our blog post. Enjoyed our write up? Please share it. Help another person find it. Thank you so much for going through it.
Learn More Report this page